Go Deal Now

 

 

Everyone will have his or her own theory on the subject of Tools You Need to Install a New Bathtub .

Installing a bath tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is additionally a moderately tough project. If the old bathtub is readily obtainable, the project can relocate speedily; if you need to open a wall to get rid of the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will require an assistant to leave the old bathtub and embeded in the brand-new one. Ensure you have actually qualified on your own for the work as well as fit attempting it. Instead of working with a professional to take control of a halfway-completed task, it is better to take into consideration employing one before you start. Chances are you may require a specialist plumber to make tube connections.
This post will help you set up a brand-new bathtub in your shower room if you have actually already purchased a brand-new bathtub and don't require to transform the arrangement of your previous water pipes.
Your tools as well as product checklist ought to make up the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you need to replace old taps with new ones as a part of your setup, then the first thing you must do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been removed, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, after that you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer provided backnut. As soon as the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Installing the Bath tub

Utilizing the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the bathtub till the spirit level reviews level.
To mount faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water and examine all joints and brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and also sealing around the bath tub should wait up until the bath tub has been made use of at least once as this will certainly settle it into its last position.

 

 

Getting ready for the Installment

First of all, the supporting framework provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to make sure that if the tap features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to stop pressure on the bath tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its final placement.

 

 

Tiling Around the Tub

In the location where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to difficulties with wetness and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to blend in your components and also installations. They are offered in tubes as well as cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealer can break fairly very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a passionate person who reads about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that editorial was worth the trouble. If you liked our post please do not forget to share it. Thank you so much for going through it.

Schedule Today